ATV61HD45Y Schneider
ATV61HD45Y Schneider
Opis
variable speed drive ATV61 - 45kW / 690V - 50HP / 575V - IP20
Tehnične lastnosti
| Glavno | |
| Serija izdelka | Altivar 61 |
| Izdelek ali sestavni del | variable speed drive |
| [Us] Nazivna napajalna npetost | 500...690 V - 15...10 % |
| product specific application | pumping and ventilation machine |
| network number of phases | 3 phases |
| component name | ATV61 |
| line current | 51 A for 600 V 3 phases 37 kW / 50 hp 55 A for 690 V 3 phases 37 kW / 50 hp 62 A for 500 V 3 phases 37 kW / 50 hp |
| asynchronous motor control profile | voltage/frequency ratio, 5 points voltage/frequency ratio, 2 points voltage/frequency ratio - Energy Saving, quadratic U/f flux vector control without sensor, standard |
| motor power kW | 37 kW, 3 phases at 500 V 45 kW, 3 phases at 690 V |
| switching frequency | 2.5...4.9 kHz adjustable 2.5...4.9 kHz with derating factor |
| maximum transient current | 70.8 A for 60 s, 3 phases |
| assembly style | with heat sink |
| nominal switching frequency | 2.5 kHz |
| EMC filter | Level 3 EMC filter |
| type of polarization | no impedance for Modbus |
| motor power hp | 50 hp, 3 phases at 575 V |
| prospective line Isc | 22 kA for 3 phases |
| communication port protocol | CANopen Modbus |
| option card | communication card for APOGEE FLN communication card for LonWorks communication card for METASYS N2 communication card for Modbus Plus communication card for Modbus TCP communication card for Modbus/Uni-Telway multi-pump card communication card for Profibus DP communication card for Profibus DP V1 communication card for BACnet communication card for CC-Link controller inside programmable card communication card for DeviceNet communication card for Ethernet/IP communication card for Fipio I/O extension card communication card for Interbus-S |
| synchronous motor control profile | vector control without sensor, standard |
| Komplementarno | |
| network frequency | 47.5...63 Hz |
| Višina | 630 mm |
| Teža izdelka | 68 kg |
| local signalling | 1 LED (red)drive voltage: |
| Širina | 320 mm |
| Globina | 290 mm |
| tightening torque | 0.6 N.m (AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1...LI6, PWR) 41 N.m, 360 lb.in (L1/R, L2/S, L3/T, U/T1, V/T2, W/T3, PC/-, PO, PA/+, PA, PB) |
| Omejitve napajalne napetosti | 425-759 V |
| protection type | against exceeding limit speed: drive power removal: drive short-circuit between motor phases: drive thermal protection: drive motor phase break: motor power removal: motor thermal protection: motor against input phase loss: drive break on the control circuit: drive input phase breaks: drive line supply overvoltage: drive line supply undervoltage: drive overcurrent between output phases and earth: drive overheating protection: drive overvoltages on the DC bus: drive |
| operating position | vertical +/- 10 degree |
| output voltage | <= power supply voltage |
| electrical connection | terminal 2.5 mm² / AWG 14 (AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1...LI6, PWR) terminal 150 mm² / 300 kcmil (L1/R, L2/S, L3/T, U/T1, V/T2, W/T3, PC/-, PO, PA/+, PA, PB) |
| Označevanje | CE |
| transmission rate | 4800 bps, 9600 bps, 19200 bps, 38.4 Kbps for Modbus on terminal 9600 bps, 19200 bps for Modbus on front face 20 kbps, 50 kbps, 125 kbps, 250 kbps, 500 kbps, 1 Mbps for CANopen |
| type of cable | with an IP21 or an IP31 kit: 3 wire(s)IEC cable at 40 °C, copper 70 °C / PVC with UL Type 1 kit: 3 wire(s)UL 508 cable at 40 °C, copper 75 °C / PVC without mounting kit: 1 wire(s)IEC cable at 45 °C, copper 70 °C / PVC without mounting kit: 1 wire(s)IEC cable at 45 °C, copper 90 °C / XLPE/EPR |
| insulation resistance | > 1 mOhm 500 V DC for 1 minute to earth |
| supply frequency | 50...60 Hz - 5...5 % |
| accuracy | +/- 0.6 % (AI1-/Al1+) for a temperature variation 60 °C +/- 0.6 % (AI2) for a temperature variation 60 °C +/- 1 % (AO1) for a temperature variation 60 °C |
| maximum switching current | R1, R2: 2 A at 250 V AC inductive load, cos phi = 0.4 and L/R = 7 ms R1, R2: 2 A at 30 V DC inductive load, cos phi = 0.4 and L/R = 7 ms R1, R2: 5 A at 250 V AC resistive load, cos phi = 1 and L/R = 0 ms R1, R2: 5 A at 30 V DC resistive load, cos phi = 1 and L/R = 0 ms |
| discrete output type | configurable relay logic: (R1A, R1B, R1C) NO/NC - 100000 cycles configurable relay logic: (R2A, R2B) NO - 100000 cycles |
| response time | <= 100 ms in STO (Safe Torque Off) R1A, R1B, R1C <= 7 ms, tolerance +/- 0.5 ms R2A, R2B <= 7 ms, tolerance +/- 0.5 ms |
| discrete input logic | negative logic (sink) (LI1...LI5), > 16 V (state 0), < 10 V (state 1) positive logic (source) (LI1...LI5), < 5 V (state 0), > 11 V (state 1) negative logic (sink) (LI6)if configured as logic input, > 16 V (state 0), < 10 V (state 1) positive logic (source) (LI6)if configured as logic input, < 5 V (state 0), > 11 V (state 1) |
| product destination | asynchronous motors synchronous motors |
| acceleration and deceleration ramps | automatic adaptation of ramp if braking capacity exceeded, by using resistor S, U or customized linear adjustable separately from 0.01 to 9000 s |
| analogue output type | AO1 software-configurable current, analogue output range 0...20 mA, impedance: 500 Ohm, resolution 10 bits AO1 software-configurable voltage, analogue output range 0...10 V DC, impedance: 470 Ohm, resolution 10 bits AO1 software-configurable logic output 10 V, 20-20 mA |
| physical interface | 2-wire RS 485 for Modbus |
| transient overtorque | 130-130 % of nominal motor torque +/- 10 % for 60 s |
| torque accuracy | +/- 15 % in open-loop mode, without speed feedback |
| data format | 8 bits, 1 stop, even parity for Modbus on front face 8 bits, odd even or no configurable parity for Modbus on terminal |
| frequency resolution | analog input: 0.024/50 Hz display unit: 0.1 Hz |
| connector type | 1 RJ45 (on front face) for Modbus 1 RJ45 (on terminal) for Modbus male SUB-D 9 on RJ45 for CANopen |
| analogue input number | 2 |
| motor slip compensation | can be suppressed automatic whatever the load adjustable not available in voltage/frequency ratio (2 or 5 points) |
| discrete output number | 2 |
| regulation loop | frequency PI regulator |
| transmission frame | RTU for Modbus |
| analogue output number | 1 |
| minimum switching current | 3 mA at 24 V DC for configurable relay logic |
| method of access | slave CANopen |
| speed range | 1-100 in open-loop mode, without speed feedback |
| discrete input number | 7 |
| linearity error | +/- 0.15 % of maximum value (AI1-/Al1+) +/- 0.15 % of maximum value (AI2) +/- 0.2 % (AO1) |
| number of addresses | 1-127 for CANopen 1-247 for Modbus |
| braking to standstill | by DC injection |
| discrete input type | programmable (LI1...LI5)24 V DC (<= 30 V), with level 1 PLC - 3500 Ohm switch-configurable (LI6)24 V DC (<= 30 V), with level 1 PLC - 3500 Ohm switch-configurable PTC probe (LI6)0-6 probes - 1500 Ohm safety input (PWR)24 V DC (<= 30 V) - 1500 Ohm |
| analogue input type | AI1-/Al1+ bipolar differential voltage: +/- 10 V DC 24 V max, resolution 11 bits + sign AI2 software-configurable current: 0...20 mA, impedance: 242 Ohm, resolution 11 bits AI2 software-configurable voltage: 0...10 V DC 24 V max, impedance: 30000 Ohm, resolution 11 bits |
| supply | internal supply for reference potentiometer (1 to 10 kOhm): 10.5 V DC, +/- 5 %, <10 mA with overload and short-circuit protection internal supply: 24 V DC (21-27 V), <200 mA with overload and short-circuit protection external supply: 24 V DC (19-30 V) |
| braking torque | <= 125 % with braking resistor 30 % without braking resistor |
| speed accuracy | +/- 10 % of nominal slip 0.2 Tn to Tn without speed feedback |
| sampling duration | 2 ms +/- 0.5 ms (AI1-/Al1+) - analog input 2 ms +/- 0.5 ms (Al2) - analog input 2 ms +/- 0.5 ms (AO1) - analog output 2 ms +/- 0.5 ms (LI1...LI5) - discrete input 2 ms +/- 0.5 ms (LI6)if configured as logic input - discrete input |
| isolation | between power and control terminals |
| continuous output current | 52 A at 2.5 kHz, 575 V - 3 phases 54 A at 2.5 kHz, 690 V - 3 phases 59 A at 2.5 kHz, 500 V - 3 phases |
| output frequency | 0.1-500 Hz |
| Okolje | |
| Temperatura okoliškega zraka za delovanje | -10-50 °C (without) 50-60 °C (with derating factor) |
| IP stopnja zaščite | IP20 on upper part without blanking plate on cover conforming to EN/IEC 60529 IP20 on upper part without blanking plate on cover conforming to EN/IEC 61800-5-1 IP21 conforming to EN/IEC 60529 IP21 conforming to EN/IEC 61800-5-1 IP41 on upper part conforming to EN/IEC 60529 IP41 on upper part conforming to EN/IEC 61800-5-1 IP54 on lower part conforming to EN/IEC 60529 IP54 on lower part conforming to EN/IEC 61800-5-1 |
| Stopnja onesnaženosti | 3 conforming to EN/IEC 61800-5-1 3 conforming to UL 840 |
| Temperatura okoliškega zraka za skladiščenje | -25-70 °C |
| relative humidity | 5-95 % without condensation conforming to IEC 60068-2-3 5-95 % without dripping water conforming to IEC 60068-2-3 |
| Nadmorska višina delovanja | <= 1000 m without 1000...2260 m with current derating 1 % per 100 m |
| Certifikati izdelkov | GOST NOM 117 UL DNV C-Tick CSA |
| Standardi | EN 61800-3 environments 1 category C3 EN/IEC 61800-3 EN 61800-3 environments 2 category C3 EN 55011 class A group 2 EN/IEC 61800-5-1 IEC 60721-3-3 class 3C2 UL Type 1 |
| Odporno proti udarcu | 15 gn for 11 ms conforming to EN/IEC 60068-2-27 |
| Odpornost proti vibracijam | 1 gn (f= 13-200 Hz) conforming to EN/IEC 60068-2-6 1.5 mm peak to peak (f= 3-13 Hz) conforming to EN/IEC 60068-2-6 |
| Elektromagnetna kompatibilnost | conducted radio-frequency immunity test level 3 conforming to IEC 61000-4-6 electrical fast transient/burst immunity test level 4 conforming to IEC 61000-4-4 electrostatic discharge immunity test level 3 conforming to IEC 61000-4-2 radiated radio-frequency electromagnetic field immunity test level 3 conforming to IEC 61000-4-3 voltage dips and interruptions immunity test conforming to IEC 61000-4-11 |
| dielectric strength | 3110 V DC between earth and power terminals 5345 V DC between control and power terminals |
| noise level | 63.7 dB conforming to 86/188/EEC |
